For engineers. Desktop software: your STEP files are read on your computer and never uploaded.

Don't design in the dark.

See which choice drives the cost before the design is frozen. Diogenes plans the part the way a shop would: the process, the stock, the machine, the setups, the tools and every cut. Then it prices each step, so you can see what a material, a process or a volume really costs.

The machining plan Diogenes priced, played back in the app. The cycle time on the right is the time of these cuts, not a rate per kilo.

One part, priced 11 ways.

Diogenes checks every process in its library against the part. 11 of them can make it, and each gets a full price at every volume from 100 to a million a year. Milled from plate, the housing costs $18.96 at 500 a year. Die casting starts at $96.24 for 100 a year, because so few parts pay for the die, and falls to $5.59 at a million.

There is a catch, and Diogenes says so. The casting routes need a casting alloy (A356 or A380) instead of 6061. That is a design change, so milling stays the headline price until you decide to make it, even where sand casting, at $16.00, comes in lower.

Plaster casting barely moves with volume, $22.39 at 100 a year and $14.69 at a million: each plaster mould is poured once, so there is little tooling to spread. Five of the 11 processes shown; the chart in the app shows them all.

Cost per part against yearly volume for the sensor housing, milled and cast, as Diogenes sweeps it $5 $10 $20 $50 $100 100 1k 10k 100k 1M parts a year Milled Plaster cast Investment cast Sand cast Die cast
Cost per part, US dollars, both scales logarithmic. The dashed line is the housing's 500 a year.

The plan behind 13.92 min.

Read from the estimate. Each of these is a line in the app you can open and change.

Stock
plate blank 115 × 85 × 35 mm, 0.924 kg, bought sawn to size; the finished part is 0.24 kg
Material price
$8.32/kg ($5.30/kg metal plus the plate premium); 0.69 kg of chips sold back at 42% of the metal price, $1.53
Setups
2, flipped on soft jaws
Setup per batch
1.8 h for 100 parts: technician at $40.47/hr, and the machine standing idle
Roughing
255 cm³ comes off the blank in all. Roughing runs 3.8 min with a 25 mm cutter at up to 577 cm³ a minute in the open areas, smaller cutters into the corners
Finishing
33 faces, each pass chosen by the surface finish it needs
Holes
7 drilled, 6 tapped, 1 finished bore
Tools
13 in a 20-pocket magazine, 19 changes at 4.5 s
Machine
Haas VF-2, 11.2 kW continuous, lowest capital cost of 8 that fit
Machine rate, mill and robot cell
$12.04/hr: $5.42/hr the mill, $6.62/hr the robot cell
Rate an efficient shop would quote
$41/hr
CAM programming, one time
87 min
Loading
robot cell, $3.12 a part less than one operator shared across machines; this job pays back its share of the shared cell in 1.9 years

This is an efficient shop: two shifts, robot loading. Put an operator at the machine and the same part costs $31.03 ($83/hr); on one shift, $33.32 ($92/hr). The operator line makes most of the difference.

Volume decides the mould.

For the work light's front bezel at 20,000 a year, Diogenes prices a one-cavity mould: $0.41 a part on a 13.3 s cycle. Raise the volume to 1,000,000 a year and it prices 1, 2, 4 and 8 cavities and keeps the cheapest per part.

Bezel20,000 / yr1,000,000 / yr
Cavities18
Feedcoldhot runner
Presslowest cost per part of those that take the mouldArburg 370 A600 kNHaitian MA3800 III3,800 kN
MouldaluminiumP20 steel
Coolingfrom the thickest wall, 2.49 mm9.2 s9.9 s
Full cycle13.3 s16.3 s
Per part$0.41$0.20
A cut-away view of the eight-cavity mould, one cycle at real speed, in the app. The other mould half, the base plates, the ejectors, the screw and the cooling lines are hidden. The hot runner drops into each part and fills all eight cavities and the colour shows how far each part has cooled. The parts turn green once they are cool enough to come out, then the mould opens and they drop: the same 16.3 s the price is built on. Under the mould, the cycle bar shows where in the shot it is, and the curve shows the temperature in the middle of the thickest wall falling from the melt to the point where the part can be ejected, which is why cooling is the longest step.

59 process cost models, 30 countries.

Each model works from how its machines run, and cites the handbook, datasheet or public statistic behind its numbers. They cover:

Machining

3-axis, 4-axis, 5-axis and 3+2 milling, turning, mill-turn.

Plastics

Injection moulding, thermoforming, rotational moulding, extrusion, injection and stretch blow moulding, foam converting, bead foam and EPP moulding, plastic sheet cutting, rubber moulding.

Casting

Die, low-pressure, vacuum, squeeze, semi-solid, permanent mould, sand, investment, plaster and centrifugal casting, with cores.

Forging and forming

Closed-die, open-die, ring rolling, upset, cold heading and cold forging, press coining, fabricated rings, aluminium extrusion, powder metal, metal injection moulding, tube bending, coil springs.

Sheet metal

Press brake, stamping, deep drawing, hot forming, plate blanking, photo etching, with laser, plasma, waterjet or punch blanking.

Electronics, additive and more

Circuit board assembly, wire harness, coil and motor winding. Metal printing (LPBF, EBM), prepreg autoclave composites, glass containers and glass covers, pulp moulding, cut-and-sew seat covers. Heat treatment and surface finishing are added as steps.

A tool you can argue with.

Change the inputs that matter

Volume, country, material, process, machine. The whole part prices again, and the breakdown shows which line moved.

Sources on every line

Cutting data and cycle laws cite the handbook and page. Rates cite the public statistic and its date. Each line says whether it was measured, derived or assumed.

Your files stay home

Installed software. STEP and STL files are read on your machine and never uploaded.

See it cost a part like yours.

A 30-minute video call. Bring a drawing to show on screen, or describe the part in a few words. Nothing needs to be sent to me.

The sample is the housing from the home page, as the app exports it. Or write to me directly: daniel@diogenescost.com

  1. A call. I cost a part like yours, live, from a few facts (material, size, volume, country) and open every line while you ask questions.
  2. A trial on your computer. You install Diogenes and cost your own drawings. They stay on your machine.
  3. Then you decide. Put Diogenes' prices next to what you pay your suppliers today, and decide whether it's worth a license.

Rather have it done for you?

I can tear down your product, cost every part in Diogenes and hand you the report: what each part should cost, how it is made, where its price comes from, and which suppliers are furthest from it. Then I help you build the negotiation plan: which parts to take up and in what order, what to ask each supplier, and the numbers to bring to the table.

Ask about a teardown and report